![]() ![]() The DIMASSOC system variable is set to 0. The dimension variable DIMASSOC is set to 1.Įxploded dimensions – contain a collection of separate objects rather than a single dimension object. Non-associative dimensions do not change when the geometric objects they measure are modified. Non-associative dimensions – selected and modified with the geometry they measure. The DIMASSOC system variable is set to 2. Dimensions in a layout may be associated to objects in model space. ![]() Each of these can be quickly defined as follows.Īssociative dimensions – automatically adjust their locations, orientations, and measurement values when the geometric objects associated with them are modified. To save your changes and exit the editor, click in the drawing outside the editor.ĭimensions can be either associative, non-associative, or exploded. Click Other to display the Select Color dialog box. To apply color to selected text, choose a color from the Color list. Note that SHX fonts do not support boldface or italics. If you wish to format text in a TrueType font with boldface or italics, or to create underlined or overlined text for any font, click the corresponding button on the ribbon. Note that the MText height value is reset to 0 if its default height is not modified during creation. If you wish to change the height of the selected text, enter a new value in the Height box. If you wish to change the font of the selected text, select a font from the list. Now, on the ribbon, you can format the changes (see Figure 2). To select a paragraph, triple-click on the paragraph. To select a word, double-click on the word. To select one or more letters, click and drag the pointing device over the characters. You can override the current text style by selecting a few letters, a word, or a paragraph. There are several tools that can change text scale and justification, find and replace text, and check for spelling errors. Now you can enter text.Īlthough all entered text uses the current text style, which establishes the default font and format settings, there are several methods that allow you to customize the text appearance. To set tabs, click the ruler specifically where you want a tab stop. If you wish to indent the other lines of each paragraph, drag the paragraph slider. If you wish to indent the first line of each paragraph, drag the first-line indent slider on the ruler. The MText ribbon Contextual tab will be displayed. Specify opposite corners of a bounding box to define the width of the multi-line text object. You can also simply use the command MTEXT. ![]() Next, select the Text drop-down and select Multi-Line (see Figure 1). To create multi-line text, begin by selecting the Text panel on the Annotation tab of the ribbon. When you are ready to end the command, press Enter on a blank line.įor longer entries with internal formatting, multi-line text (mtext) can be used. Every time you press Enter or specify a point, a new text object is created. If you specify another point during this command, the cursor moves to that point, and you can continue typing. Text that would otherwise be difficult to read (if it is very small or very large) is displayed in a legible size and is oriented horizontally so that you can easily read and edit it. At the end of each line, press Enter and then you can enter more text as needed. You can enter an angle value or use your pointing device and then enter the text. Click to set the height of the text to the length of the rubber-band line. A rubber-band line is attached from the text insertion point to the cursor. Please note that this prompt is displayed only if text height is set to 0 in the current text style. If you press Enter, the program locates the new text immediately below the last text object you created, if any. Specify the insertion point for the first character. Next, select the Text drop-down and select Single Line (see Figure 1). To create single-line text, begin by selecting the Text panel on the Annotation tab of the ribbon. For short, simple entries, single-line text should be used. Some examples of annotations are notes and labels, dimensions, hatches, tables, blocks, and callouts. Annotations are basically notes or other types of explanatory objects (or symbols) that are commonly used to add information to a drawing. Back April 24th, 2012 Annotations in AutoCAD ArchitectureĪutoCAD® Architecture contains great annotation abilities. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |